Determination of viscouselastic properties of pressure fire hoses with a diameter of 150 mm

 

Sergii Nazarenko

National University of Civil Defence of Ukraine

https://orcid.org/0000-0003-0891-0335

 

Gennadiy Chernobay

National University of Civil Defence of Ukraine

http://orcid.org/0000-0001-8805-3710

 

Oleksandr Kolienov

National University of Civil Defence of Ukraine

https://orcid.org/0000-0002-3736-9165

 

Pavlo Borodych

National University of Civil Defence of Ukraine

https://orcid.org/0000-0001-9933-8498

 

Borys Kryvoshei

National University of Civil Defence of Ukraine

http://orcid.org/0000-0002-2561-5568

 

Vladyslav Titarev

National University of Civil Defence of Ukraine

http://orcid.org/0000-0002-3183-1689

 

DOI: https://doi.org/10.52363/2524-0226-2021-33-12

 

Keywords: pressure fire hose, elasticity module, rigidity, hysteresis, dissipative properties

 

Abstract

The presented experimental studies to determine the viscoelastic characteristics of a pressure head fire hose of the "T" type with an inner diameter of 150 mm under static load conditions. In the course of the work, a number of full-scale tensile experiments were carried out with a sample under conditions of static loading-unloading cycles. The tests consisted of 7 cycles (mode) of loading-unloading, which were carried out with a two-minute interval. Taking into account the experimental data, the tensile stiffness of the sleeve material in the longitudinal (along the base) direction was determined. It has been established that numerous results of mechanical properties depend on the "history" of the sleeve load, that is, in the first two load modes, the rigidity is given, increased, and only then, in the next ones, they stabilized. This, together with a significant reduction in residual deformations, enhances the elastic properties of the fire hose material. The results of the studies have shown that during the first two cycles the material demonstrates the manifestation of short-term creep, which is stabilized at 5-7 modes. To general-ize the experimental studies, the results are approximated by the corresponding trend lines. Deformation curves of the samples were determined under cyclic loading-unloading conditions, which formed hysteresis loops. When analyzing the corresponding curves, it was found that: firstly, during the first two three cycles of loading-unloading, the area of the hysteresis loops decreases. Secondly, the angle of inclination of the hysteresis loops also decreased with each loading-unloading cycle. It was found that the dissipation coefficients of the sleeve material when stretched in the longitudinal direction in the first two or three test modes increases. In subsequent tests (cycle 4-7), the dissipation coefficients decrease and then stabilize at a level of 0.42.

 

References

  1. Lee, G. -C., Kim, H. -E., Park, J. -W., Jin, H. -L., Lee, Y. -S., Kim, J., -H. (2011). An expermental study and finite element analysis for finding leakage path in high pressure hose assembly. International Journal of Precision Engineering and Manu-facturing, 12, 3, 537–542. doi: 10.1007/s12541-011-0067-y
  2. Pavlouskova, Z., Klakurkova, L., Man, O. Celko, L., Svejcar, J. (2015). As-sessment of the cause of cracking of hydraulic hose clamps. Engineering Failure Analysis, 56, 14–19. doi: 10.1016/j.engfailanal.2015.05.014
  3. Dong-Hyun, Y., Beom-Seon, J., Ki-Ho, Y. (2017). Nonlinear finite element analysis of failure modes and ultimate strength of flexible pipes. Marine Structures, 54, 50–72. doi: 10.1016/j.marstruc.2017.03.007
  4. Haseeb, A., Jun, T., Fazal, M., Masjuki, H. (2011). Degradation of physical properties of different elastomers upon exposure to palm biodiesel. Energy, 36, 3, 1814–1819. doi: 10.1016/j.energy.2010.12.023
  5. Cho, J., Yoon, Y., Seo, C., Kim, Y. (2015). Fatigue life assessment of fabric braided composite rubber hose in complicated large deformation cyclic motion. Finite Elements in Analysis and Design, 100, 65–76. doi: 10.1016/j.finel. 2015.03.002
  6. Cho, J., Yoon, Y. (2016). Large deformation analysis of anisotropic rubber hose along cyclic path by homogenization and path interpolation methods. Journal of Mechanical Science and Technology, 30, 2, 789–795. doi: 10.1007/ s12206-016-0134-5
  7. Roland, T., David, M., Oliver, S., Roman, L. (2019). Mechanical performance of textile-reinforced hoses assessed by a truss-based unit cell model. International Journal of Engineering Science, 141, 47–66. doi: 10.1016/j.ijengsci. 2019.05.006
  8. Larin, O. (2015). Probabilistic model of fatigue damage accumulation in rub-berlike materials. Strength of Materials, 47, 6, 849–858.
  9. Larin, O., Morozov, O., Nazarenko, S., Chernobay, G., Kalynovskyi, A., Kova-lenko, R., Fedulova, S., & Pustovoitov, P. (2019). Determining mechanical properties of a pressure fire hose the type of «T». Eastern-European Journal Of Enterprise Tech-nologies, 6 (7 (102)), 63–70. doi: 10.15587/1729-4061.2019.184645
  10. Nazarenko, S., Kovalenko, R., Asotskyi, V., Chernobay, G., Kalynovskyi, A., Tsebriuk, I., Shapovalov, O., Shasha, I., Demianyshyn, V., Demchenko, A. (2020). De-termining mechanical properties at the shear of the material of «T» type pressure fire hose based on torsion tests. Eastern-European Journal Of Enterprise Technologies, 5 (7 (107)), 45–55. doi: 10.15587/1729-4061.2020.212269
  11. Fedorko, G., Molnar, V., Dovica, M., Toth, T., Fabianova, J. (2015). Failure analysis of irreversible changes in the construction of the damaged rubber hoses. Engineering Failure Analysis, 58, 31–43. doi: 10.1016/j.engfailanal. 2015.08.042
  12. Stepanov, O., Bratoljubova, E., Shirokov, A. (2012). Issledovanie vlijanija razlichnyh faktorov na prochnost' napornyh pozharnyh rukavov pri gidravlicheskom vozdejstvii. Tehnologija tekstil'noj promyshlennosti, 4, 105–108.